久久久精品一二三区,国产图片二区,少妇淫妇久久久久久久,久久超碰pro

產品中心 PRODUCT CENTER

濟南成林·值得信賴Worthy of trust

全國咨詢熱線

0531-82820798

苗經理(13806401238)

電話:0531-82820798 

手機:13806401238

QQ:981562958

郵箱:981562958@qq.com

地址:濟南市槐蔭區張莊路8—3號


公司新聞

當前位置: 首頁>>新聞中心>>公司新聞

變速器維修后的匹配和自適應方法

發布日期: 2022-05-28 來源: http://fdwhkj.cn/ 點擊: 0

匹配方法
Matching method
方法1:啟動車輛使發動機與變速器達到正常工作溫度,掛前進檔行駛20米,慢踩剎車,直至車速為0保持檔位10S,同時觀看10組數據流,然后掛R檔行駛20米,慢踩剎車,直至車速為0保持檔位,同時觀看11組數據流,兩項OK了,完成自適應學習!
Method 1: start the vehicle to make the engine and transmission reach the normal operating temperature, shift to the forward gear for 20 meters, step on the brake slowly until the vehicle speed is 0 and keep the gear for 10s, and watch 10 groups of data streams at the same time, then shift to the R gear for 20 meters, step on the brake slowly until the vehicle speed is 0 and keep the gear, and watch 11 groups of data streams at the same time. The two items are OK, and the adaptive learning is completed!
方法2:啟動車輛使發動機與變速器達到正常工作溫度。掛前進檔使車速達到70km/h以上(手動模式要升至6檔),然后點剎10次或在檔停車10秒以上;再掛倒檔行駛20米以上,然后在檔停車10秒以上即完成自適應學習。
Method 2: start the vehicle to make the engine and transmission reach normal operating temperature. Engage the forward gear to make the vehicle speed reach more than 70km/h (the manual mode should be raised to gear 6), and then brake for 10 times or stop in gear for more than 10 seconds; The self-adaptive learning is completed by driving in reverse gear for more than 20 meters, and then stopping in reverse gear for more than 10 seconds.
方法3:啟動車輛使發動機與變速器達到正常工作溫度。掛前進檔不踩油門,ECU會提高發動機轉速使之車速提高,向前行駛20,慢踩剎車,使之車速為0,要保持檔位,等待10S,然后掛R檔,行駛20米,方法同前進檔!
Method 3: start the vehicle to make the engine and transmission reach normal operating temperature. When engaging the forward gear without pressing the accelerator, the ECU will increase the engine speed to increase the vehicle speed. Drive forward for 20 minutes, slowly press the brake to make the vehicle speed 0. Keep the gear, wait for 10s, then engage the R gear and drive for 20 meters. The method is the same as that of the forward gear!
濟南自動變速箱維修
自適應方法
Adaptive method
1.以低功率驅動發動機,直到ATF油溫達到60-90°C。
1. drive the engine with low power until the ATF oil temperature reaches 60-90 ° C.
2、車輛停車時,發動機怠速,踩下制動踏板,從n變?yōu)镈,并保持此狀態約3秒。重復此過程五次。然后用同樣的方法從n變?yōu)镽。
2. When the vehicle is stopped, the engine is idling, press the brake pedal, change from n to D, and maintain this state for about 3 seconds. Repeat this process five times. Then change from n to R in the same way.
3、當車輛靜止時,換到D檔,小負載(油門踏板位置15-25%,測量數據塊02/2)將車輛加速到4檔(約80km/h)。然后讓汽車滑行到大約40公里/小時(不要踩剎車踏板),然后用適度的力量踩下剎車踏板,讓汽車停下來。車輛停止后,必須將車輛保持在“d”狀態約10秒鐘(踩下制動踏板)。重復整個步驟III六次。(6次0km/h->80->40->0)
3. When the vehicle is stationary, shift to gear d, and accelerate the vehicle to gear 4 (about 80km/h) with a small load (accelerator pedal position 15-25%, measurement data block 02/2). Then let the car slide to about 40 km / h (do not step on the brake pedal), and then press the brake pedal with moderate force to stop the car. After the vehicle is stopped, the vehicle must be kept in the "d" state for about 10 seconds (press the brake pedal). Repeat the entire step III six times. (6 times 0km/h->80->40->0)
4、將車輛加速至約70km/h并手動將其換至5檔(尖端)。然后以80-100nm發動機功率(見測量數據塊09)的恒定速度行駛約3-4分鐘。
4. Accelerate the vehicle to about 70km/h and manually shift it to 5th gear (tip). Then drive at a constant speed of 80-100nm engine power (see measurement data block 09) for about 3-4 minutes.
5、將車輛加速至約90km/h并手動將其換至6檔(尖端)。然后以80-100nm發動機功率(見測量數據塊09)的恒定速度行駛約2-3分鐘。
5. Accelerate the vehicle to about 90km/h and manually shift it to 6th gear (tip). Then drive at a constant speed of 80-100nm engine power (see measurement data block 09) for about 2-3 minutes.
6、濟南自動變速箱維修提醒各位,當車輛靜止時,小負載將車輛加速至100km/h左右(油門踏板位置15-25%,測量數據塊02/2)。然后讓汽車滑行到40km/h左右(不要踩剎車踏板),再用一點力踩剎車踏板讓車停下。重復整個步驟六到五次。
6. Jinan automatic transmission maintenance reminds you that when the vehicle is stationary, a small load will accelerate the vehicle to about 100km/h (accelerator pedal position 15-25%, measurement data block 02/2). Then let the car slide to about 40km/h (do not step on the brake pedal), and then step on the brake pedal with a little force to stop the car. Repeat the entire procedure six to five times.
變速器維修后的匹配和自適應方法內容講解完畢,您可以來關注我們網站fdwhkj.cn,了解咨詢更多方面的要點!
After explaining the matching and adaptive methods after transmission maintenance, you can follow our website www.jnbsx COM, learn more about the key points of consulting!

關鍵詞: 自動變速器故障檢測一般程序 自動變速箱常見幾種狀況有哪些? 汽車變速箱進水后怎么維修? 汽車變速箱基礎知識的特點講解 自動變速箱維修保養要注意什么?

魯公網安備 37010402000808號

  • 聯系電話
    0531-82820798
  • 微信咨詢
  • 久久大胆视频| 大香蕉久久观看| 久久熟女、| 日本影视久久久久久久久久久久| 国产黑料网刘玥区在线播放| 成人电影一区| 久久久久真人精品| 国产金品乱码| 刘玥 久久精品| 一级黄片免费看95国产精品| 国产香焦一级黄色片冈站| 天天日日插进去| 欧美一区自拍| 久久久久夜夜夜夜国产综合| 日韩欧美一区二区在线不卡3d | 天天日天天爽.| 午夜国产色综合| 亚洲免费午夜激情综合二区| 老熟女不卡免费| 亚洲视频主页日本电影院| 日本一区二区不卡手机视频| 91伊人欧美| 久久久 AV片一区二区| 91直播高清一区二区视频| 欧美人妻少妇自拍| 男人资源天堂岛| 夜夜夜夜人人人人| 青青草吧av| 亚洲AV成人精品一区二区三区四区| 最好看的一区二区三区四区| 扣b视频在线看| 午夜在线毛片| 国产3at∨在线视频| 成人黄色在线9| 99久久久精品无码| 久久国产青青精品| 国产区色欲精品| 国产精品自在欧美| 人妻卖淫被颜射| 91老肥熟妇| 日韩欧美精品直播|